Follow Us on LinkedIn Follow Us on YouTube

  1. CLR 2161 / CLH 5100

    Heat Cure, UV resistant, outdoor, low-stress, large mass casting epoxy system for instrument and power transformers. Extremely tough, epoxy compound. this system was specifically developed for use on outdoor instrument and power transformers. The cured material exhibits excellent thermal stability and thermal cycling characteristics. This product meets UL94-HB flammability requirements. CLR 2161 / CLH 5100

  2. CLR 3080 / CLH 6372

    General Adhesive room temperature cure. Resistant to Toluene, Ethanol, Aviation Gas and Diesel Fuel. A low viscosity, two component, chemical resistant epoxy system. Post cured material has excellent resistance to most petroleum based fuels and solvents during exposure at ambient and elevated temperatures. CLR 3080 / CLH 6372

  3. CLR 3507 / CLH 6230

    A semi-flexible, 100% solid, epoxy system. This product was specifically developed for potting / casting of electrical and electronic components. The long pot life of the material makes it suitable for large mass castings or heat induced curing with minimal stress. Product passes UL94-HB in-house flammability testing. For a more rigid system, CLR 3517 / CLH 6230 is recommended. CLR 3507 / CLH 6230

  4. CLR 3516 / CLH 6230

    Room temperature cure, filled, semi-flexible epoxy system. Long pot life material is suitable for large mass casting or heat-induced curing with minimal stress. This product was specifically developed for potting / casting of electrical and electronic components. The long pot life of the material makes it suitable for large mass castings or heat induced curing with minimal stress. For a softer system, CLR 3506 / CLH 6230 is recommended. CLR 3516 / CLH 6230

  5. CLS 9600

    High Temperature. A single component, 100% solids, low viscosity, impregnating compound for coils and transformers. This product is also suitable for sand casting. CLS 9600

  6. CLS 9611

    A low viscosity, single component, epoxy potting and encapsulating compound. The product has excellent stability and good adhesion to a wide range of substrates. This product meets UL 94-HB flammability requirements. Heat Cure Single Component semi-flexible epoxy potting and encapsulating system. Product is suitable for potting ferrites and pressure sensitive components in electrical and electronic applications. CLS 9611

  7. CLS 9616

    Heat Cure. Single Component semi-flexible epoxy potting and encapsulating system. Product is suitable for potting ferrites and pressure sensitive components in electrical and electronic applications. Low viscosity. The product has excellent stability and good adhesion to a wide range of substrates. This product meets UL94-HB flammability requirements. CLS 9616

  8. XID 1681 / XHD 1652

    A two component polyurethane casting system. Product has long pot-life and cures to a hardness of 65 Shore D. XID 1681 / XHD 1652

  9. XP 61862 / CLI 4161

    UL 94-V0 certified fast setting, potting / casting PU for transformers, coils, and electronic components. A two component, low viscosity, polyurethane casting system, specifically designed for casting transformers, coils and electronic components. Product has excellent thermal shock resistance. XP 61862 / CLI 4161

  10. XR 11483 / CLH 6260

    Excellent fuel resistance. Suitable for automotive fuel sensors. A two component, chemical resistant epoxy casting system. The cured product has improved thermal conductivity for applications where heat dissipation from thermally sensitive devices is required. Cured product is resistant to Ethanol, Gasoline, and Diesel, when exposed to these chemicals at ambient or elevated temperatures. XR 11483 / CLH 6260

  11. XRD 1014 / XHD 1015

    High temperature clear epoxy. An unfilled, heat resistant, clear laminating system. Products low viscosity gives the system excellent wet-out properties to fibreglass and other reinforcing fibres. The material exhibits high physical strengths and modulus with moderate post cure temperatures. XRD 1014 / XHD 1015

  12. XRD 1018 / XHD 1019

    1:1 Mix Ratio, 130°C Operating, General Purpose, Low cost. A two component, room temperature cure semi-flexible, flame retardant, epoxy system. The system was developed for potting/casting of electrical and electronic components. Its use of non-abrasive fillers and convenient 1 to 1 ratio by volume, make it ideal for use in machine dispensing equipment. This product meets UL94-V0 in house flammability testing. XRD 1018 / XHD 1019

  13. XRD 1116 / XHD 1117

    Room Temperature Cure Epoxy system suitable for potting and casting electrical / electronic components. 2:1 machine dispense friendly mix. Suitable for processing in automatic dispense equipment. This product meets UL94-V1 in house flammability testing. XRD 1116 / XHD 1117

  14. XRD 1116 / XHD 1158

    2:1 machine dispense friendly mix. A filled, room temperature cure, two component epoxy system. The product is suitable for potting / encapsulating electrical and electronic components. The use of non-abrasive fillers and the convenient mix ratio makes it suitable for processing in automatic dispense equipment. This product meets UL94-V1 in house flammability testing. XRD 1116 / XHD 1158

  15. XRD 1116 / XHD 1281

    Room temperature cure epoxy system suitable for potting and casting electrical / electronic components. 2:1 machine dispense friendly mix. The product is suitable for potting/encapsulating electrical and electronic components. The use of non-abrasive fillers and the convenient mix ratio makes it suitable for processing in automatic dispense equipment. This product meets UL94-V1 in house flammability testing. XRD 1116 / XHD 1281

  16. XRD 1321 / CLH 5185

    Machine dispense friendly, tough, casting epoxy system. Increased flexibility when compared to CLR 1831 family. A two component, low stress, heat cure epoxy system specifically developed for use on instrument and power transformers. The product if filled with non-abrasive fillers, making the product suitable for machine dispensing. The cured material exhibits excellent thermal stability and thermal cycling endurance. Product meets UL 94-HB flammability requirements. XRD 1321 / CLH 5185

  17. XRD 1347 / XHD 1348

    The product cures to a shore hardness of 50 A, low viscosity, soft system. A two component, very flexible epoxy system. XRD 1347 / XHD 1348

  18. XRD 1501 / CLH 6090

    4:1 Ratio, soft system. A two component unfilled, flexible epoxy system. Product features low viscosity, long pot life and cures to a shore hardness of 70A. XRD 1501 / CLH 6090

  19. XRD 1575 / XH 61418

    2:1 machine dispense adhesive. Bonding abrasive wheels and disks. A two component epoxy system suitable for potting, casting and adhesive applications. Product gels quickly and has good thermal cycling endurance. Material is filled with non-abrasive fillers making it suitable for machine dispensing. XRD 1575 / XH6 1418

Results 41 - 59 of 59

Filters