1. CLR 1020 / CLH 6021

    Semi-flexible epoxy adhesive and casting system. An unfilled, semi-flexible two component epoxy system. Its low mixed viscosity makes it suitable for potting and encapsulating electronic components. CLR 1020 / CLH 6021

  2. CLR 1026 / CLH 6021

    Low viscosity, semi-flexible. An unfilled, semi-flexible two component epoxy system. Its low mixed viscosity makes it suitable for potting and encapsulating electronic components. CLR 1026 / CLH 6021

  3. CLR 1066 / CLH 6930

    Large mass casting, 30-minute pot life. Masses larger than 6Lbs. A two component, filled, room temperature cure epoxy system.the product has a low exotherm and low shrinkage, making it suitable for castings larger than 3 kgs. CLR 1066 / CLH 6930

  4. CLR 1180 / CLH 6560

    Room temp cure, Excellent shock resistance. An exceptional epoxy casting system with excellent thermal and mechanical shock resistance. CLR 1180 / CLH 6560

  5. CLR 1180 / CLH 6930

    Room temp cure, excellent shock resistance. An exceptional epoxy laminating system with excellent thermal and mechanical shock resistance. Product is suitable for a variety of applications. CLR 1180 / CLH 6930

  6. CLR 1183 / CLH 6560

    Shock resistant, General purpose epoxy. A two component epoxy casting system. product has low shrinkage and excellent shock resistance. CLR 1183 / CLH 6560

  7. CLR 1190 / CLH 6025

    General purpose variable substrate adhesive. A medium viscosity, unfilled casting system. It is suitable for large mass castings and exhibits good impact resistance. CLR 1190 / CLH 6025

  8. CLR 1190 / CLH 6560

    Low viscosity, RT cure. Impact resistant. Excellent thermal cycle. An exceptionally tough epoxy casting system with excellent low temperature thermal and mechanical shock resistance. CLR 1190 / CLH 6560

  9. CLR 1415 / CLH 6220

    Low Density, Flame Retardant, 120°C Operating. A two component, low density, room temperature curing, flame retardant, epoxy potting/casting compound. CLR 1415 / CLH 6220

  10. CLR 1796 / CLH 6580

    UL 94-V0 system for potting and casting small electronic parts that require thermal shock and thermal cycling performance. A two component, low viscosity, room temperature cure epoxy system. Material has yellow card UL94-V0 rating, and contains non abrasive fillers suitable for meter mix dispense. CLR 1796 / CLH 6580

  11. CLR 1946 / CLH 6500

    Product is recommended for potting and encapsulating applications. A two component, room temperature cure semi-flexible epoxy system. The system was developed for potting / casting of electrical and electronic components. Its use of non abrasive fillers and convenient 1:1 ratio by volume, makes it ideal for use in machine dispensing equipment. CLR 1946 / CLH 6500

  12. CLR 3080 / CLH 6372

    General Adhesive room temperature cure. Resistant to Toluene, Ethanol, Aviation Gas and Diesel Fuel. A low viscosity, two component, chemical resistant epoxy system. Post cured material has excellent resistance to most petroleum based fuels and solvents during exposure at ambient and elevated temperatures. CLR 3080 / CLH 6372

  13. XR 11483 / CLH 6260

    Excellent fuel resistance. Suitable for automotive fuel sensors. A two component, chemical resistant epoxy casting system. The cured product has improved thermal conductivity for applications where heat dissipation from thermally sensitive devices is required. Cured product is resistant to Ethanol, Gasoline, and Diesel, when exposed to these chemicals at ambient or elevated temperatures. XR 11483 / CLH 6260

  14. XRD 1014 / XHD 1015

    High temperature clear epoxy. An unfilled, heat resistant, clear laminating system. Products low viscosity gives the system excellent wet-out properties to fibreglass and other reinforcing fibres. The material exhibits high physical strengths and modulus with moderate post cure temperatures. XRD 1014 / XHD 1015

  15. XRD 1018 / XHD 1019

    1:1 Mix Ratio, 130°C Operating, General Purpose, Low cost. A two component, room temperature cure semi-flexible, flame retardant, epoxy system. The system was developed for potting/casting of electrical and electronic components. Its use of non-abrasive fillers and convenient 1 to 1 ratio by volume, make it ideal for use in machine dispensing equipment. This product meets UL94-V0 in house flammability testing. XRD 1018 / XHD 1019

Results 1 - 15 of 15